Electrical panel upgrades in Fayetteville, NC
A 200-amp panel replacement typically runs $2,500 to $4,000 installed, permit and inspection included, and is usually done in one day. Here is how to tell if you need one and what to expect.

How to tell a panel needs replacing
Most panels do not fail all at once. They give you one of these signs first.
Breakers that keep tripping
One trip is a breaker doing its job. The same breaker tripping again and again means the circuit is overloaded or something is failing, and it should be looked at.
A warm or buzzing panel
A panel should be quiet and cool to the touch. Warmth, buzzing, a scorched smell or rust inside the box means a connection is going bad.
A fuse box instead of breakers
Fuse boxes were built for houses that used far less power than yours does now. They are usually small, and they leave no room to add anything.
No room for new circuits
If every slot is taken, a new circuit has nowhere to go. A larger panel fixes that properly.
An EV charger, heat pump or hot tub
These are big, steady loads. Before one goes in, somebody has to check that the panel and the service can carry it.
Panel upgrade or service upgrade?
The panel is the metal box with the breakers in it. A panel upgrade swaps that box and its breakers for a new one. The amount of power coming into the house stays the same. You get new, reliable equipment and more room for circuits.
The service is everything that brings power from the utility to that box: the overhead or underground line to the house, the meter base outside, and the heavy cable from the meter to the panel. A service upgrade, also called a service change, makes that whole path bigger, for example taking an older house up to 200 amps. It involves the power company, because they have to disconnect and reconnect the house.
Which one you need depends on what is there now and what you plan to add. We look at the panel, the meter base and the loads in the house, then tell you plainly.
What a 200-amp panel upgrade costs
A 200-amp panel replacement in the Fayetteville area typically costs $2,500 to $4,000 installed. That includes the electrical permit and the inspection.
Where a job lands in that range comes down to the house. A panel in a tight or hard-to-reach spot takes longer. So does a panel with a lot of circuits to move over, or old wiring at the panel that has to be corrected so the job passes inspection. Grounding that needs to be brought up to the current code adds work too.
If the meter base or the outside service equipment also has to be replaced, the job is a full service upgrade rather than a panel replacement. That is priced by written estimate before any work starts. An estimate appointment is $100, credited to the job when you go ahead, and we come out, look at everything and put the number in writing.
What happens on the day
Most panel replacements are finished in one working day.
Permit and scheduling first
Before the day, we pull the electrical permit. If the job needs the power company to disconnect the house, we schedule that with Duke Energy, Fayetteville PWC, Lumbee River EMC or South River EMC.
Power goes off
The power to the house is off while the panel is changed. Plan for no lights, no air conditioning or heat, and no internet for most of the workday. Charge phones and move anything that cannot wait.
Old panel out, new panel in
We remove the old panel, mount the new one, reconnect every circuit to a new breaker and label each one so you can read it.
Inspection
The local inspections office checks the work. We meet the inspector, so you do not have to.
Power back on
On a panel replacement we turn the power back on and test the circuits with you. On a service upgrade the power company reconnects the house, and we coordinate that for you.
When a SPAN smart panel makes more sense
Sometimes the panel is fine and the real problem is capacity. You want an EV charger or a heat pump, and the service is close to its limit.
A bigger service is one answer. A SPAN smart panel is another. It replaces the main panel and manages the big loads in the house so they do not all draw at once. That often lets an EV charger or heat pump go on an existing 200-amp service without a utility service upgrade.
We are a SPAN Authorized Installer and we also do conventional upgrades, so we have no reason to push one over the other. We will tell you which fits your house.
Panel upgrades, answered
How much does a 200 amp panel upgrade cost in Fayetteville, NC?
A 200-amp panel replacement typically runs $2,500 to $4,000 installed, including the permit and inspection. A full service upgrade with new outside equipment is priced by written estimate before work starts.
How long is the power off during a panel upgrade?
Plan for the power to be off for most of the workday. Most panel replacements are done in one day. If the power company has to disconnect and reconnect the house, we coordinate that and tell you ahead of time what to expect. On a full service upgrade the power company reconnects after the inspection passes. If that lands late in the day, the reconnect can be the next morning, and we tell you before we start so you can plan for it.
Do I need a permit to replace an electrical panel?
Yes. Panel and service work needs an electrical permit and an inspection from the local inspections office, such as the City of Fayetteville or Cumberland County. We pull the permit and meet the inspector.
Should I replace my old fuse box?
In most cases, yes, when you are ready. A fuse box is usually too small for a modern house and has no room for new circuits. We can look at it and tell you what shape it is in.
Can I add an EV charger without upgrading my panel?
Sometimes. It depends on the size of your service and what is already on it. We check the capacity first, and if it is tight, a SPAN smart panel may avoid a bigger service. See EV charger installation.
Do you do panel upgrades outside Fayetteville?
Yes. Our shop is in Raeford, and we work in Hoke, Cumberland, Harnett, Sampson and Moore counties, including Hope Mills, Spring Lake and the off-post neighborhoods around Fort Bragg. You can book online or call (910) 973-8600.
Ready when you are
Book online, pick the times that work, and the office confirms by text. Or call (910) 973-8600.
Other services
Where we work Fayetteville · Raeford and Hoke County · Hope Mills · Fort Bragg area · Spring Lake · Lillington, Dunn and Erwin